For sale / Wanted
- Written by: Administrator
Bücker Jungmann E131, rebuilt in Spain by Jesus Ballester (Bucker Prado).
Based in Chateauroux-Villers, France (LFEJ).
Originaly built in 1956 and rebuilt from 2002 to 2004.
Engine : Tigre 150 HP, inverted flight oil and gas systems.
Spanish wood propeller.
Dacron covering (2.000/cm2), wings and fuselage new.
Battery and auxiliary start-up socket.
New altimeter and instruments.
Double gas circuits, Christen hand pump.
Aircraft like new, only flown for 12 hours.
The battery needs to be changed.
Price : 105.000 €.
FRANCE
06.64.90.86.07
- Written by: Giles
Let me know if you are interested: I could have several made and leave them at cost price, which of course depends on the number...
Gilles
- Written by: Brian Karli
- Written by: Administrator
This is an original German Bucker with pre moritorium restrictions (none) It is powered by a Lycoming IO-320 engine and has been hangared since restoration in 1989. there are many years left on this bird. More info and photos may be found at http://2aw.com/bucker.htm
- Written by: Steve
The part numbers to order are: 1315600402,1315700402 (single), 1315703003,1315600303 (double).
- Written by: Rudolph Herrgen
I have a Swedish built Bücker Bestmann Bü 181 B-1 for sale in Germany. Built in 1945 with a Hirth HM 500 engine.
The plane is complete in every detail, was never damaged, but needs a complete overhaul to put it back into the air. It is presently displayed in a small museum near Cologne.
I have substantial technical documentation, a spare Hirth HM 504 and lots of spare parts.
For more information contact me at
Rudolf
- Written by: Administrator
- Written by: Douglas M. James
I need the 2 P-lead fittings that screw into the case of the magnetos.
Thanks for your help.
Scottsdale, AZ
- Written by: jennefer whicher
- Sold -
Bucker Jungmann Undercarriage - Spanish made CASA
Accident damaged undercarriage for sale. Spreader bars and tripod damaged and not offered though could be used for spare ends. Remainder in undamaged condition except where indicated.
1 set bolts
1 set joints
2 ea. fairings, woodwork damaged metalwork bent, easily repairable
2 ea. axle for original drum brake
2 ea. main-shaft, with the end nuts.
set of springs and seals, and distance parts
2 ea. inside piston and tensile tube, top attachment broken on one but weldable.
2 wheels with drum brakes and relatively new brake pads.
2 Tyres (quite old).
$1500 ono
Extra set of Bitz springs, almost new.
$100
Contact Jenny:
- Written by: Blumenthal Thomas
Can you help me?
Thank`s
Thomas from old Germany/Bavaria.
- Written by: Loichat Arnaud
thanks
Please to contact me
LOICHAT ARNAUD
RUE DE L'ARC-EN-CIEL 16
CH-2300 LA CHAUX-DE-FONDS
SWITZERLAND
EMAIL:
Phone : 0041 (0)79 682 39 31
- Written by: Doug James
New Die Cut Tigre Gasket Set: Set includes: 2 crankcase gaskets 1 nose bowl gasket 1 accessory housing gasket 1 filter housing gasket 3 oil filter bowl gaskets 3 oil filter nut gaskets 1 oil pump gasket 1 oil screen gasket 1 fuel pump gasket 1 generator gasket 1 carb/manifold gasket 1 oil breather gasket 1 starter gasket 4 silicone valve cover gaskets 8 valve pushrod gaskets Price of complete set (as listed) $125 plus shipping. Available for both Tigre G-V and G-IV models. Contact
WANTED:
I'm in need on a couple completly non-usable, broken, but complete engines..
G-IV-A, or A2 or B is fine. I don't need any of the major componets, just all the hardware... for two or three engines.
Crashed, broken in half, rusted out...anything considerd. I have two ready to rebuild on the shelf, but ALL of my hardware on the external side of the engine has been lost while shipping. Every washer, bolt, nut, clip, tube, bracket and screw....
Let me know what you might have to sell me.
Matt Chapman
610-659-6598 Cell
ps....gaskets are ready to cut, have 30 yards of material, just need time. Pistons and rings are once again front and center. Both 125 and 150....
- Written by: Brian Karli
Shirts available in blue, white or yellow.
Hats with Bucker logo: $17.99
- Written by: Gilles Tatry
Looking for Tigre spinner plans for having one made...
Anyone can help?
Gilles
- Written by: John LaBarre
Hirth HM504 A-2 Engines and any parts wanted. Information about the whereabouts of Hirth engines and parts, also wanted.
Please contact John D. LaBarre,
- Written by: Gary Novack
I have the following items for sale:
1. New Bucker Streamlined Supplemental Tail Wires : 20& 3/8-inch and 25-
inch overall length. Asking $250.00 for a set of 4 wires.
I have two sets of wires available.
2. One set of original Spanish Bucker Magnesium Wheels and Sky Classic's
wheel spats.Wheels are bead blasted and ready for your paint. Asking $
250.00
3. One set of sky classic's wheel spats for Cleveland Wheels Asking $150.00
Thanks , Gary Novack (610)-823-7543 or
IAC #0137628
- Written by: Jerry Wells
Lyc 0-320 160HP 3700TT 1400SMOH Inverted oil. Recovered in 1988.
Contact: Jerry Wells 717 865 0720 (h) 717 821 0999 (cell)
jwells@lmf
- Written by: Douglas M. James
I need an oil cooler with the attached check valve for the Tigre Engine, 150 HP
Doug James, Scottsdale, AZ
- Written by: John LaBarre
- Written by: John LaBarre
Now available: Brand new CNC machined 6061 T6 aluminum fuel tank flop tube fitting. Threads into existing tank boss. Accepts AN6 flop tube fitting as used on Aircraft Spruce's flop tube. Externally, the fitting accepts AN6 fittings, for attachment to output line or hose. Same dimensions as original fitting, but designed with inset flange for safety wiring the flop tube's hex fitting in any position. Photos available via email upon request. $80.00, includes shipping to Lower 48 US states only. All other shipping costs extra. 6061 T6 has excellent corrosion resistance, but hard anodizing is available for this part, extra cost. Contact: John D. LaBarre 513 227 7254 email: